| Customization: | Available |
|---|---|
| After-sales Service: | Avalibale |
| Warranty: | Yes |
| Shipping Cost: | Contact the supplier about freight and estimated delivery time. |
|---|
| Payment Methods: |
|
|---|---|
| Support payments in USD |
| Secure payments: | Every payment you make on Made-in-China.com is protected by the platform. |
|---|
| Refund policy: | Claim a refund if your order doesn't ship, is missing, or arrives with product issues. |
|---|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
The structure consists of: walking chassis, engine, torque converter, front and rear four-drive bridge, loading device, feed
Bucket, discharge hopper, extended discharge hopper, frame, stirring tank, stirring special planetary reducer, hydraulic system, electric control
System, automatic water system, etc., its characteristics are as follows:
The traveling system is from the engine to the front and rear axle through the torque converter, the front and rear transmission shaft. Hydraulic steering four
The drive form greatly reduces the turning radius and is more suitable for work on the site, especially for construction in small Spaces. hydrodynamic
The torque converter reduces the impact on the engine and prolongs the engine life. Use electrovaleless variable speed electric control valve for walking
It controls.
The hydraulic system is 5-6 square with constant power variable piston pump, and 1.2-4 square with gear pump to reduce the engine
Power loss.
The rotation of the mixing tank is driven by the hydraulic motor through the special planetary reducer, and the output shaft of the planetary reducer can be
To achieve a certain Angle of swing, in order to meet the bad road conditions of the stirring tank beat. The mixing tank of the mixer truck is controlled
The speed valve can accurately control the mixing speed of the mixing tank.
| Driving mode | Center enclosed |
| Fuel category | Diesel |
| Engine model | Yunnei 490 |
| Engine power | 46KW |
| Gearbox model | 530(12th gear high and low speed) |
| After | Dongfang 1061 |
| Front | SL178 |
| Brakng mode | Air brake |
| Rear wheel track | 1630mm |
| Front wheel tread | 1630mm |
| Frame | Main girder:height 120mm*width 60mm*thickness 8mm. Botton beam:height 60mm*width 80mm*thickness 6mm. |
| Tank volme | 2 Fang |
| Tank wall thickness | 4mm |
| Front tire model | 700-16 Mine Tire |
| Rear tire model | 700-16Mine Tire (Twin) |
| Vehicle size | Length 5950mm*wwidth 1650mm*height 2505mm |
| Load/ton | 5 |
| Remarks | Can be customized acording to the requiements of 3,4,5 |
Important steps of mixer operation:
Check whether there is water in the water tank before work, and there is no need to fill it with water pump; Check the fuel in the diesel tank
Bit, whether it can be guaranteed to use; Check the oil level of the hydraulic tank; Check whether the tire is damaged, the barometer is normal, and the bolts
Whether it is loose, etc. Make sure that the water valve is on, the car wash water valve is off, and the car wash bucket vent switch is off
Closed state. Fill each lubricating part with lubricating oil.
Before starting or turning off the engine, ensure that each control handle is in the middle position, and then start after confirming
The mixer truck.
After starting, check whether the table instrument is normal, when the barometer reaches 4mpa, other instruments are normal, you can
Press the brake pedal, hang the low gear, release the air brake, and the mixer starts to walk.
First, push the control rod of the mixing tank to the open position to open the mixing mode of the mixing tank; Then turn on the water
Quantity controller water; Open the electronic weighing controller, start feeding, push the bucket to lift the big arm control handle to the big arm
To the lowest, the bucket flattens the shovel material, collects the bucket, lifts the big arm, weighs it, continues to rise after weighing, and the bucket mouth is aligned
After the quasi-feeding port, open the bin door to discharge the material, close the bin door after discharging the material, and carry out the next loading. When weighing accumulated excess
To obtain the weight, open the excess part of the bin door to remove, and then go up to the feed port to discharge. Until cement, sand and stone reach
Specify the weight. The mixing tank rotates slowly during the feeding process. After adding the material, increase the mixing speed and wait to be stirred evenly
After blending, unload the material to the required position. Connect the extended dump hopper to the dump hopper, and switch the control rod of the mixing tank to the discharge position
(Mixing tank reversed), discharge completed, collect the extended discharge hopper. Repeat operation to continue working.
The mixing tank needs to be cleaned after the completion of the daily work to prevent the cement from drying and causing the tank capacity to decrease. Operation step
Sudden: open the water valve, add water into the tank, idling for a few minutes, and then unload the water at high speed. Clean the outside of the car thoroughly
And fix the long discharge hopper. Stop the mixer, pull the handbrake, turn off the electronic scale, and turn off the fire.
){kind=link}